The CK61100X3000 is a heavy duty flat bed CNC lathe for large shafts, rolls, flanges and tubes up to 3000 mm turning length. It swings 1000 mm over the bed and 630 mm over the cross slide, travels 500 mm in X and 3000 mm in Z, and weighs 6500 kg. Overseas after-sales service and CE certified machines.
The CK61100X3000 is a heavy duty flat bed CNC lathe built for workpieces that a standard lathe cannot swing or hold: large shafts, rolls, flanges, tube sheets and hydraulic cylinders up to 3000 mm turning length. It swings 1000 mm over the bed, 630 mm over the cross slide, and carries a 6500 kg machine mass on a 5400 mm long bed that is 1900 mm wide. X axis travel is 500 mm and Z axis travel is 3000 mm, both under CNC control, so the machine holds a programmed diameter along the full length of a long part instead of being fed by hand. External turning, internal boring, facing, grooving and thread cutting are all done in one clamping, which is the difference between one accurate part and a part that has been re-chucked three times.
Mass is the difference between a big lathe and a big lathe that cuts accurately. The CK61100X3000 weighs 6500 kg, and that weight sits in a heavily ribbed one-piece cast iron bed with wide, hardened and ground guideways. On a workpiece of this size the cutting force is large and the overhang is long, so the bed has to absorb vibration before it reaches the tool tip; a lighter machine will chatter on the same cut and leave the pattern visible in the finish. The hardened ways keep their geometry under continuous heavy load and are not damaged by the chips and coolant that come with roughing. The result is a machine that holds a diameter from the chuck end to the tailstock end of a 3000 mm shaft, not only on a short test piece in front of the chuck.
Two diameters are quoted for this lathe and they are not the same thing. The Φ1000 mm figure is the swing over the bed: the largest blank that physically clears the bed when the machine is open. The Φ630 mm figure is the swing over the cross slide: the largest diameter that can still be turned with the tool post and tooling in position. The 370 mm difference in diameter, 185 mm of radius, is taken up by the cross slide, the tool post and the tool itself. For cylindrical turning, plan the part against Φ630 mm. For short facing work, large flanges and interrupted end work, the part can be Φ1000 mm because the tool only reaches the face and does not need to clear the slide. We would rather state this plainly than let a customer plan a process against a diameter the machine cannot cut.
The lathe is fitted with a four-jaw independent chuck, which is the correct choice for heavy and irregular blanks: each jaw is set independently, so a rough casting, a forged roll or an out-of-round repair job can be indicated true instead of being forced into a scroll chuck. With 3000 mm of Z travel and a bed 5400 mm long, long shafts are supported and machined in one set-up rather than being joined from shorter pieces. The Φ105 mm spindle bore allows bar work through the headstock and also lets a long boring bar pass through when internal features are machined deep inside a tube or a cylinder barrel. Steady rests and follow rests, together with the control and tooling package, are quoted to suit the actual workpiece rather than supplied as a fixed list.
The CK61100X3000 is used in heavy machinery, shipbuilding and offshore, steel and rolling mill maintenance, hydraulic equipment, mining, power generation and general heavy repair workshops. Typical parts are large shafts, rolls, flanges, tube sheets, cylinder barrels, couplings, sleeves and threaded connectors. It machines carbon steel, alloy steel, stainless steel and cast iron, with the exact cutting data depending on the workpiece material, hardness, size and machining requirement. Where a part is too long or too heavy for a standard lathe, this is the class of machine that keeps the job in-house instead of subcontracted.
| Model | CK61100X3000 |
| Max. swing over bed | Φ1000 mm |
| Max. swing over cross slide | Φ630 mm |
| Max. turning length | 3000 mm |
| Max. machining diameter | Φ1000 mm |
| Max. bar diameter | Φ500 mm |
| Spindle bore | Φ105 mm |
| X / Z axis travel | 500 / 3000 mm |
| Net weight | 6500 kg |
| Machine dimensions (L × W × H) | 5400 × 1900 × 2000 mm |
The machine is shipped as a complete unit with the dimensions stated above, 5400 × 1900 × 2000 mm and 6500 kg net weight, so lifting points, floor capacity and door clearance should be checked before delivery. We support the installation with foundation and leveling guidance, commissioning checks and operator training on the control and on the four-jaw chuck set-up. Spare parts and technical support are handled by our overseas after-sales service, and the machines are CE certified. For bar work, the spindle bore of Φ105 mm is the governing through-hole dimension; the larger bar figure in the table refers to chuck-clamped stock, and we will confirm the exact limit against your drawing before the order.
Send us the workpiece drawing, the material and the batch size, and we will confirm the CK61100X3000 configuration, price, delivery time and technical support. We provide overseas after-sales service and CE certified machines.