HOME PRODUCT Slant Bed CNC Lathe TCK50A TCK50A Slant Bed CNC Lathe

PRODUCT

TCK50A Slant Bed CNC Lathe
TCK50A Slant Bed CNC Lathe TCK50A Slant Bed CNC Lathe TCK50A Slant Bed CNC Lathe TCK50A Slant Bed CNC Lathe TCK50A Slant Bed CNC Lathe

TCK50A Slant Bed CNC Lathe

Product ID : TCK50A
Product Tags :
Product Attributes :

The TCK50A is a 45-degree slant bed CNC lathe for disc and short-shaft parts: Φ560 mm swing over the bed, Φ260 mm over the slide, 350, 500 or 800 mm machining length and a 3000 rpm spindle with a Φ66 or Φ86 mm bore. CE certified, with installation and overseas after-sales support.

Product Description

TCK50A Slant Bed CNC Lathe

The TCK50A is the larger frame in our 45-degree slant bed lathe range. Where the smaller TCK46A is built for bar work and small turned parts, the TCK50A carries a Φ560 mm swing over the bed, a 3000 rpm spindle and machining lengths from 350 to 800 mm — enough structure to hold flanges, bearing housings, valve bodies and short shafts without the part fighting the machine.

Three machining lengths are built on the same platform, so the machine can be specified to the parts you actually run rather than to a catalogue default. The machine is CE certified, ships with a complete manual and electrical set, and is backed by our overseas after-sales service network.

Key Features

  • Φ560 mm swing over bed — the clearance limit, i.e. the largest blank that rotates over the bed without fouling.
  • Φ260 mm swing over slide — the working limit once the tool is mounted. Plan your process against this figure.
  • 3000 rpm spindle — sized for the larger chuck and heavier part this frame carries, not for micro-turning.
  • Φ66 mm or Φ86 mm spindle bore — bar stock through the spindle on the standard bore, up to Φ86 mm on the long-bed configuration.
  • 350 / 500 / 800 mm machining length — one platform, three bed lengths, so you do not pay for bed you never use.
  • 3200 to 4500 kg of cast structure — mass scales with bed length, which is what keeps finish stable on a longer part.
  • 45-degree slant bed — chips fall clear of the guideways instead of being dragged across them.

Φ560 Over the Bed, Φ260 Over the Slide — Read Both Numbers

These two figures are not interchangeable, and quoting only the larger one is how a machine gets bought for work it cannot do. The Φ560 mm swing over bed is a clearance figure: it tells you the largest blank that will physically rotate over the bed. The Φ260 mm swing over the slide is the working figure: with the tool mounted on the slide, this is the diameter range you can actually turn.

On the TCK50A the gap between the two is wide, because the bed is sized for the long-bed variant and for fixtures that sit off-centre. In practice you plan against Φ260 mm. The extra clearance is what lets you chuck an odd-shaped casting or a part on a faceplate without hitting the bed — useful, but not a machining capacity.

If your part needs more than Φ260 mm turned diameter, tell us the drawing before you order. A different model on the same platform is the honest answer, and we will say so rather than let the machine arrive undersized.

Three Machining Lengths on One Platform

The TCK50A is listed with 350, 500 and 800 mm machining length on a common 45-degree bed. The standard machine is the 350 mm version; 500 mm and 800 mm are the long-bed variants on the same platform, designated TCK50A-500 and TCK50A-800.

Bed length is not a free option. A longer bed adds weight, adds floor space and adds the deflection that comes with any longer cantilever. That is why the three variants carry different figures: weight rises from 3200 kg to 4500 kg, overall length from 2700 mm to 3300 mm, and the long variant is available with a Φ86 mm spindle bore for larger bar.

Choose by the parts you run most, not by the longest part you might run once. If 90 percent of your work is under 350 mm, the short bed holds tolerance better on those parts. If you routinely run 600 mm shafts, take the 800 mm variant and accept the larger footprint.

3000 rpm Spindle and Φ66 or Φ86 Bore

Cutting speed is diameter times rpm. At 3000 rpm a Φ80 mm part runs at about 754 m/min — comfortably inside carbide finishing range for steel, with headroom to reduce speed where the material needs it. The same spindle still turns a Φ200 mm flange at a sensible surface speed without running out of low-end torque.

The standard bore is Φ66 mm, which puts continuous bar work up to Φ66 mm within reach: stock feeds through the spindle, the part is cut off, the cycle repeats. The Φ86 mm bore on the long-bed variant extends that to larger bar and lets a longer part pass through the spindle instead of hanging out of the chuck.

Spindle speed and bore are matched to the frame. A 3000 rpm spindle on a 3200–4500 kg machine is a production speed, not a laboratory figure — it is meant to be used all shift, not quoted once.

Why a Slant Bed Matters in Production

On a flat bed lathe, chips land on the guideways and stay there. On a part running at 3000 rpm in a production cycle, that means abrasive swarf being dragged across a precision surface several hundred times per shift. A slant bed lets chips fall into the chip pan, which keeps the guideways clean and holds accuracy over months instead of weeks.

The slant layout also brings the spindle and turret closer to the operator, which shortens setup and tool change time. On disc parts with short cycle times, that handling time is a larger share of cost per piece than the cutting itself.

Applications and Typical Parts

The TCK50A is used where disc-type and short-shaft parts are turned in quantity:

  • Hydraulics and pneumatics — valve bodies, manifolds, cylinder end caps, union flanges
  • Bearings and transmission — bearing housings, bearing seats, gear blanks, bushings
  • Automotive — hubs, brake components, sensor housings, flanged shafts
  • General engineering — flanges, spacers, pulleys, threaded adaptors, pump bodies

It machines carbon steel, alloy steel, stainless steel, cast iron, brass and aluminium with the appropriate inserts and cutting parameters. For castings and forgings with interrupted cuts, tell us the blank condition so the configuration and tooling are matched to it.

CNC System and Configuration Options

The machine is supplied with a production CNC system and configured against your process. Options typically specified with this model include:

  • Chuck type and size — three-jaw, independent four-jaw or collet chuck for bar work
  • Bar feeder interface matched to your stock diameter and length
  • Turret arrangement, with driven tooling where the process needs cross-drilling or milling
  • Tailstock for shaft work on the 500 mm and 800 mm variants
  • Parts catcher and chip conveyor for unattended cycles
  • Coolant through-tool and high-pressure coolant for deep-hole or stainless work

Configuration drives both cycle time and price. Final specification is confirmed against your drawing and monthly quantity before quoting, so the machine that arrives matches the process you described.

Installation, Commissioning and Support

At 3200 to 4500 kg, the TCK50A ships as a complete machine and needs a level floor and a normal industrial power supply, not a special foundation. We supply the foundation drawing, electrical schematic and parameter list before the machine leaves the factory, so site preparation can start while it is in transit.

Commissioning covers levelling, spindle warm-up and runout check, turret alignment, tool setting and a first-part run against your drawing. Training for operators and maintenance staff is included. Our overseas after-sales service network keeps spare parts and technical support available for the working life of the machine, and responds in English, Spanish, Russian or Arabic.

Technical Specifications

Item Unit TCK50A
Max. swing dia. over bed mm Φ560
Max. swing dia. over slide mm Φ260
Max. processing length mm 350 / 500 / 800
Spindle speed rpm 3000
Spindle hole diameter mm 66 / 66 / 86
Weight KG 3200 / 3600 / 4500
Machine size mm 2700 / 2700 / 3300 × 2000 × 2000

The table lists the full platform: three machining lengths, the two spindle bore sizes and the corresponding weight and dimensions. Your quotation will state the exact variant supplied. Note once more that Φ560 mm is swing over the bed (clearance) while Φ260 mm is swing over the slide (working limit) — plan the process against Φ260 mm.

Why Choose TCK50A

  • CE certified — documentation supplied for EU import and site acceptance.
  • Overseas after-sales service — engineers and spare parts support in Europe, with response in four languages.
  • Three bed lengths, one platform — specify the length your parts need, not the longest one on the list.
  • 3000 rpm with Φ66 or Φ86 bore — disc work and bar work on the same machine.
  • 3200–4500 kg of structure — mass behind the cut, so finish does not depend on light passes.
  • 45-degree slant bed — chips clear the guideways, accuracy holds over months of production.

Send us a drawing, the blank condition and the monthly quantity. We will confirm which TCK50A variant suits the part, quote the configuration, and tell you plainly if another model fits better.

Online Inquiry