The CK6160X1000 CNC Lathe is a heavy-duty flat bed turning machine that swings 600 mm over the bed and 500 mm in cutting diameter, so large flanges, hubs, valve bodies and heavy shafts that a 500 mm class lathe cannot take are machined on one machine. It holds 1000 mm of processing length, passes Φ82 mm through the spindle, and carries a Φ75 mm tailstock sleeve for supporting heavy workpieces.
The CK6160X1000 CNC Lathe is a heavy-duty flat bed turning machine built for large-diameter, short-to-medium length work: flanges, hubs, bearing housings, valve bodies, brake discs, sleeves and heavy shafts. It swings 600 mm over the bed and 310 mm over the slide, cuts up to Φ500 mm in diameter and holds 1000 mm of processing length, so parts that a 500 mm class lathe has to turn down or refuse altogether are finished here in one setup. The Φ82 mm spindle bore passes bar stock and tube, the Φ75 mm tailstock sleeve supports heavy overhanging work, and the 0.001 mm minimum displacement unit on both feed axes holds size on parts where a few hundredths decide whether the bearing seats press in correctly. External turning, internal boring, facing, grooving and threading are completed in a single clamping, so the datum never moves between operations.
The number that defines the CK6160X1000 is the 600 mm swing over the bed. A 500 mm class lathe cannot take a 600 mm flange at all; on this machine the same flange, hub or bearing housing is clamped on a Ø500 mm chuck and machined without the special fixturing or the vertical boring mill detour that usually eats the schedule. The 310 mm swing over the slide means the tool still reaches the work when the part is large, and the 500 mm cutting diameter leaves room for the interrupted cuts typical of cast hubs and valve bodies. For a job shop that turns anything between a 100 mm sleeve and a 600 mm flange, this is one lathe covering the whole range instead of two machines with a gap in the middle.
The CK6160X1000 is built on a high-rigidity flat bed cast in one piece of high-strength iron and aged before machining, so the structure settles before it is ground rather than after the machine is installed. That rigidity is what allows heavy depth of cut on large-diameter work without the chatter that shows up as a rippled finish, and it is why the machine holds tolerance across the full length of a 1000 mm part. The guideways are hardened and ground, keeping the sliding surfaces accurate over years of production instead of developing the soft spots that appear as taper along a long shaft. Deep roughing cuts at the same spindle load shorten the cycle, and the finish stays consistent from the first part of the batch to the last.
The spindle system is designed for both bar work and heavy chuck work. The Φ82 mm bore passes bar and tube as standard; Φ105 mm and Φ130 mm bores can be specified when the shop runs larger bar stock. The Φ75 mm tailstock sleeve is oversized for a lathe of this size because heavy, long parts need real support at the far end — a small quill deflects under load, and the deflection turns into runout at the workpiece shoulder. Precision ball screws and hardened guideways on both axes hold the 0.001 mm minimum displacement unit, so the machine can interpolate tapers and radii and return to a reference surface without losing position between passes.
The CK6160X1000 is delivered as standard with a GSK CNC system, a manual 3-jaw chuck, a manual tailstock, a standard tool post, a cooling system, centralized lubrication, a work light and a full protective enclosure. A hydraulic 3-jaw or 4-jaw chuck and a hydraulic tailstock can be specified for higher clamping force and shorter cycle times, and a hydraulic or servo turret with 6 or 8 stations keeps tool changes fast and repeatable on parts that need several tools. An automatic chip conveyor clears chips continuously on long runs, and a bar feeder lets the lathe keep producing without an operator loading each workpiece. A spindle oil cooler, pneumatic system, steady rest, follow rest and precision measuring probes are available, and Siemens, Fanuc and KND control systems can be fitted on request.
The CK6160X1000 is widely used in automotive parts, construction machinery, mining equipment, energy equipment, hydraulic equipment, general machinery manufacturing and general-purpose component processing. With a 600 mm swing over bed, a 500 mm cutting diameter and an 82 mm spindle bore it handles flanges, hubs, bearing housings, valve bodies, brake discs, pulleys, sleeves and heavy shafts. It machines carbon steel, stainless steel, alloy steel, cast iron, aluminium and copper alloys across general turning, bore finishing, threading and related flat bed CNC processes. The actual application depends on the workpiece material, size and machining requirements.
| Model | CK6160X1000 |
| Max. swing over bed | Φ600 mm |
| Max. swing over slide | Φ310 mm |
| Max. cutting diameter | Φ500 mm |
| Max. processing length | 1000 mm |
| X/Z axis max. stroke | 300 (1000/1500) mm |
| X/Z axis min. displacement unit | 0.001 mm |
| Spindle hole diameter | Φ82 (105/130) mm |
| Tailstock sleeve diameter | Φ75 mm |
| Overall dimensions (L×W×H) | 2940 × 1400 × 1700 mm |
The CK6160X1000 gives a 600 mm swing, a 500 mm cutting diameter and 1000 mm of machining length with an 82 mm spindle bore and a Φ75 mm tailstock sleeve, so heavy flanges, hubs and shafts are finished in one clamping on a machine that costs far less than the vertical boring mill alternative. It combines a rigid aged casting with a 0.001 mm minimum displacement unit, then adds hydraulic chuck, hydraulic or servo turret, chip conveyor and bar feeder options so it can keep running unattended. Overseas after-sales service and CE certified machines are provided.
Contact us for the CK6160X1000 CNC lathe price, delivery time, configuration options and technical support. We provide overseas after-sales service and CE certified machines.