The CK6150X2000 CNC Lathe is a heavy-duty flat bed turning machine that swings 500 mm over the bed and machines up to 2000 mm between centers, so long shafts, lead screws, rollers and tube parts that a 1000 mm lathe cannot hold are finished in a single setup. It swings 290 mm over the slide, carries an 82 mm spindle bore, and holds a 0.001 mm minimum displacement unit on both feed axes.
The CK6150X2000 CNC Lathe is a heavy-duty flat bed turning machine built for long shaft, roller, lead screw and tube work in medium-to-large batch production. It swings 500 mm over the bed and 290 mm over the slide, and with 2000 mm of maximum processing length it takes the long parts that a 1000 mm lathe has to turn in two setups and then re-align. The 82 mm spindle bore passes bar stock and tube that smaller machines reject, and the 0.001 mm minimum displacement unit on both feed axes means the machine can hold size on a long part where every error is multiplied by the length. The lathe completes external turning, internal boring, facing, grooving and threading in a single clamping, so the datum never moves between operations.
The defining number on the CK6150X2000 is the 2000 mm maximum processing length. Long shafts, lead screws, rollers, printing and packaging rollers, hydraulic cylinder rods and tube components that a 1000 mm machine turns in two setups are clamped once here, which removes both the second setup time and the re-alignment error that shows up as runout at the far end. The bed casting runs the full length of the machine as one rigid piece rather than as a bolt-on extension, so the tailstock end is as stiff as the headstock end and the machine does not lose accuracy halfway down the part. For a shop that turns long parts alongside short ones, that means one lathe instead of a short lathe plus a long-bed special.
The CK6150X2000 is built on a high-rigidity, one-piece flat bed casting that keeps the machine stiff under interrupted and continuous cuts alike. That rigidity matters more on a 2000 mm machine than on a short one, because deflection and vibration grow with the unsupported length of the workpiece. The ways are hardened and ground, so the sliding surfaces stay accurate after years of production instead of developing the soft spots that appear as taper along a long shaft. A rigid bed also allows deeper cuts at the same spindle load, which shortens the cycle on the 500 mm class of parts while keeping the finish consistent from one end of the part to the other.
The machine pairs a high-performance spindle with precision ball screws and hardened guideways on both feed axes, held to a minimum displacement unit of 0.001 mm. The 82 mm spindle bore takes bar stock and tube that a smaller lathe cannot pass. In production that shows up as a tighter dimensional spread on shafts, rollers, sleeves and threaded parts, and as a lower scrap rate when a long part is machined close to its tolerance. Because the CK6150X2000 performs external turning, internal boring, facing, grooving and threading without re-clamping, every operation removed from the route is also a datum error removed from the workpiece.
The CK6150X2000 is delivered as standard with a GSK CNC system, a manual 3-jaw chuck, a manual tailstock, a standard tool post, a cooling system, centralized lubrication, work light and a full protective enclosure. A hydraulic 3-jaw or 4-jaw chuck and a hydraulic tailstock can be specified for higher clamping force and shorter cycle times, and a hydraulic or servo turret with 6 or 8 stations keeps tool changes fast and repeatable on parts that need several tools. An automatic chip conveyor clears chips continuously on long runs, and a bar feeder lets the lathe keep producing without an operator loading each workpiece. A spindle oil cooler, pneumatic system, steady rest, follow rest and precision measuring probes are available, and Siemens, Fanuc and KND control systems can be fitted on request.
The CK6150X2000 is widely used in automotive parts, construction machinery, energy equipment, hydraulic equipment, mining equipment, printing and packaging machinery, general machinery manufacturing and general-purpose component processing. With a 500 mm swing over bed, a 2000 mm maximum processing length and an 82 mm spindle bore it handles long shafts, drive shafts, lead screws, rollers, hydraulic cylinder parts, tube components, threaded parts and medium-to-large metal rotary parts. It machines carbon steel, stainless steel, aluminium alloys and copper alloys across general turning, threading and related flat bed CNC processes. The actual application depends on the workpiece material, size and machining requirements.
| Model | CK6150X2000 |
| Max. swing over bed | Φ500 mm |
| Max. swing over slide | Φ290 mm |
| Max. cutting diameter | Φ500 mm |
| Max. processing length | 2000 mm |
| X/Z axis max. stroke | 2000 mm |
| X/Z axis min. displacement unit | 0.001 mm |
| Spindle hole diameter | Φ82 mm |
The CK6150X2000 gives a 500 mm swing and 2000 mm of machining length with an 82 mm spindle bore, so long shafts and rollers that need two setups on a short lathe are finished in one. It combines a Φ500 mm cutting diameter with a 0.001 mm minimum displacement unit, then adds hydraulic chuck, hydraulic or servo turret, chip conveyor and bar feeder options so it can keep running unattended. Overseas after-sales service and CE certified machines are provided.
Contact us for the CK6150X2000 CNC lathe price, delivery time, configuration options and technical support. We provide overseas after-sales service and CE certified machines.